Update housing and code

--add local timezone
--add sunrise/sunset calculation and LED illumination accordingly
--remove touch sensor check
--change mqtt messages

FingerprintDoorbell/lib/SparkFun_SX1509/examples/DigitalReadWriteCombined/DigitalReadWriteCombined.ino

@@ -0,0 +1,125 @@
+/*************************************************************
+  digitalReadWriteCombined.ino
+  SparkFun SX1509 I/O Expander Example: digital I/O (digitalRead/digitalWrite)
+  Jim Lindblom @ SparkFun Electronics
+  Original Creation Date: September 21, 2015
+  https://github.com/sparkfun/SparkFun_SX1509_Arduino_Library
+
+  This example demonstrates the SX1509's digitalRead and digitalWrite
+  functionality. We'll attach an active-low button to an
+  INPUT_PULLUP input and attach an LED to a pin set as OUTPUT.
+  Then whenever the button read's LOW, we'll toggle the LED.
+  Note that the code will wait until the button is released
+  before reading the SX1509 pins again.
+
+  After uploading the sketch, open your serial monitor and set
+  it to 115200 baud.
+
+  Hardware Hookup:
+  SX1509 Breakout ------ Arduino -------- Breadboard
+        GND -------------- GND
+        3V3 -------------- 3.3V
+        SDA ------------ SDA (A4)
+        SCL ------------ SCL (A5)
+        0 ---------------------------------]BTN[----GND
+        15 -------------------------------- LED+
+                                       LED- -/\/\/\- GND
+                                               330
+  Development environment specifics:
+  IDE: Arduino 1.6.5
+  Hardware Platform: Arduino Uno
+  SX1509 Breakout Version: v2.0
+
+  This code is beerware; if you see me (or any other SparkFun
+  employee) at the local, and you've found our code helpful,
+  please buy us a round!
+
+  Distributed as-is; no warranty is given.
+*************************************************************/
+
+#include <Wire.h>           // Include the I2C library (required)
+#include <SparkFunSX1509.h> //Click here for the library: http://librarymanager/All#SparkFun_SX1509
+
+// SX1509 I2C address (set by ADDR1 and ADDR0 (00 by default):
+const byte SX1509_ADDRESS = 0x3E; // SX1509 I2C address
+SX1509 io;                        // Create an SX1509 object to be used throughout
+
+// SX1509 pin definitions:
+// Note: these aren't Arduino pins. They're the SX1509 I/O:
+const byte SX1509_LED_PIN = 15; // LED connected to 15 (source ing current)
+const byte SX1509_BUTTON_PIN = 0; // Button connected to 0 (Active-low button)
+
+bool ledState = false;
+
+void setup()
+{
+  // Serial is used in this example to display the input value
+  // of the SX1509_INPUT_PIN input:
+  Serial.begin(115200);
+  Serial.println("SX1509 Example");
+
+  Wire.begin(); //Initialize I2C bus
+
+  pinMode(13, OUTPUT); // Use pin 13 LED as debug output
+  digitalWrite(13, LOW); // Start it as low
+
+
+  // Call io.begin(<address>) to initialize the SX1509. If it
+  // successfully communicates, it'll return 1.
+  if (io.begin(SX1509_ADDRESS) == false)
+  {
+    Serial.println("Failed to communicate. Check wiring and address of SX1509.");
+    digitalWrite(13, HIGH); // If we failed to communicate, turn the pin 13 LED on
+    while (1)
+      ; // If we fail to communicate, loop forever.
+  }
+
+  // Call io.pinMode(<pin>, <mode>) to set any SX1509 pin as
+  // either an INPUT, OUTPUT, INPUT_PULLUP, or ANALOG_OUTPUT
+  // Set output for LED:
+  io.pinMode(SX1509_LED_PIN, OUTPUT);
+  // Use a pull-up resistor on the button's input pin. When
+  // the button is pressed, the pin will be read as LOW:
+  io.pinMode(SX1509_BUTTON_PIN, INPUT_PULLUP);
+
+  // Blink the LED a few times before we start:
+  for (int i = 0; i < 5; i++)
+  {
+    // Use io.digitalWrite(<pin>, <LOW | HIGH>) to set an
+    // SX1509 pin either HIGH or LOW:
+    io.digitalWrite(SX1509_LED_PIN, HIGH);
+    delay(100);
+    io.digitalWrite(SX1509_LED_PIN, LOW);
+    delay(100);
+  }
+}
+
+void loop()
+{
+  // Use io.digitalRead() to check if an SX1509 input I/O is
+  // either LOW or HIGH.
+  if (io.digitalRead(SX1509_BUTTON_PIN) == LOW)
+  {
+    // Print the status of the other pin:
+    Serial.print("SX1509_BUTTON_PIN status: ");
+    // Read the pin to print either 0 or 1
+    Serial.println(io.digitalRead(SX1509_BUTTON_PIN));
+
+    // If the button is pressed toggle the LED:
+    ledState = !ledState;
+    io.digitalWrite(SX1509_LED_PIN, ledState);
+
+    // Print the status of the other pin:
+    Serial.print("SX1509_LED_PIN status: ");
+    // Read the pin to print either 0 or 1
+    Serial.println(ledState);
+
+
+    Serial.print("Waiting for button to release...");
+    while (io.digitalRead(SX1509_BUTTON_PIN) == LOW)
+      ; // Wait for button to release
+    Serial.println("Button released!");
+
+    //delay(200); //uncomment to add a small delay for  button debouncing
+  }
+}